| JET DRIVES | ||
 |
||
| 13000PD | PERFORMANCE DRIVE | |
| A True Performance Drive Providing you with the Highest Thrust and Volumn Output in a 12" Mixed Flow Bowl, 9" Impeller Drive System. We Built it "Super Beefey" to insure all the demands on a race ready pump exceeded the customers demands. | ||
 |
*Our Suction Case- Has the following features: Over Size Hand Hole clean out, Pre Bored for Race Valve, which provids a full hand hole side wall, after stock removal of the valve bore( much stronger core) Yet it provides the every day boater a hole size large enough to get his hand in, to remove any obstructions. (Danger: Always have motor off when opening Hand Hole Cover). | |
 |
*Billet Backing Plate and Oversize Knobs for the Hand Hole Cover Provides you with additional strength for todays bigger motors. | |
| *Pump is Interchangeable with most all Pumps and its mounting location. | ||
 |
*Cast thru Water inlets (inboard side) have been added to the Suction for Structual Case Strength. Both Outlets are Line Bored through Solid Casting which provide you with a Clean Inboard Connection. No additional Outboard Hoses or Transom Holes are Required.Suction also has Double Thick Side Walls to further insure the Integrety of the Suction. Load Volumn has also been Increased to meet the Demands of our Impeller and Bowl System. | |
 |
*Bearing Cap section has been braced at all support stantions and a full alloy fill is made to rear of packing gland section blending into case. One Size Repeatable Transom Plate Mounting Configuration when Transom Mounting. | |
 |
*THRUST BEARING- | |
| This is a Double Row 12 balls per row 24 total- Aggressor has a second grind tolerance called pre-clearance put on the thrust bearings to support our customers demand for a higher RPM allowance. We have tried them all and no bearing meets the demands our builders put these under. | ||
 |
*SEALS- | |
| J.M.CLIPPER - Case hard rubber with support plate & Pat.- wax coat seal urface. | ||
 |
*SHAFT | |
| We start the 13000 where most others end there line. 17-4 with a mild eat treat. Shaft is up-graded to include a double thick snap ring to provide additional Bearing support. | ||
 |
*WEAR RING | |
| Aluminium Bronze receives an additional case hardness in heat treatment bringing the alloy hardness up to a equiv.S/Steel hardness. | ||
 |
*BOWL | |
| 9 Vane is the Performance standard in reduced harmonics, absolute water control and volumn output. Also available in 7 & 11 Vane. | ||
 |
*IMPELLER | |
| Aluminium heat treated with a hard black anodize treatment. Up-Grades to Major Mag.Bronze Or Stainless Steel available. | ||
 |
*NOZZLE or DROOP | |
| Aggressor provides you with a 3 way option here at no additional charge. Standard Nozzle Housing, Std. Droop, or Short Droop. | ||
 |
*NOZZLE SYSTEMS | |
| Aggressor provides you with 3 Options also: Standard Fwd/Rev & Choice of Rudder Size, or Race Nozzle System with no Reverse includes or for an additional $ 185.00 you can have a Manual Trim Diverter. All Aggressor Nozzle Systems come include (1) Insert Choke Size for fine tunning your selection. NOTE: On Manual Trim-Shifter or Cable are not included & are extra.> | ||
| PERFORMANCE DRIVE PRICING | ||
| 13000 PD | PERFORMANCE DRIVE - Alum. Impeller Complete | $2,995.00 |
| Same except 304- SHAFT vs 17-4 | ||
| 13000 PR | PRO RACE MODEL- Mag. Impeller Complete | $3,430.00 |
| 13000 PR-S | PERFORMANCE DRIVE- S/Stl. Impeller Complete | $3,790.00 |
| ADDITIONAL OPTIONS: | ||
| -P | Full Polish | $295.00 |
| -CCP | Custom Color Paint- | $200.00 |
| -NH | NOZZLE HOUSING-SHORT | N/C |
| -D | STANDARD DROOP Droop | N/C |
| -SD | SHORT DROOP | N/C |
| -SN | STANDARD FWD./REVERSE NOZZLE WITH RUDDER | N/C |
| -RN | RACE NOZZLE (NO REVERSE) | N/C |
| -MD | MANUAL DIVERTER | $285.00 |
| -HTD | HYD. ASSY KIT FOR DIVERTER (MUST BE ORDERED WITH MANUAL DIVERTER) | $495.00 |
| (COMPLETE UNIT INCLUDING COILED STEERING WHEEL UP/DOWN SWITCH) | ||
| -BS | BOWL STUFFER | $87.50 |
| -PLS | PRE-LOADER SHAFT | $95.00 |
| -PLI | PRE-LOADER AXIAL IMPELLER | $389.00 |
| -JA | JET-AWAY- INCLUDES DOUBLE DRILL SUCTION @ BEARING CAP. | $1,250.00 |
 |
||
| SHORT PUMP VERSION Transom Mounted Shown Standard Nozzle w Reverse, Short Nozzle Housing, Standard Rudder | ||
| JET DRIVES #12000 INSERT DRIVE | ||
 |
||
| 12000 INSERT DRIVE | $2,545.00 | |
| Over Cast Wall Thickness throughout entire casting Machine Interchangable Shoe with Ride Plate and Bowl Support. Strategic Placed Water Inlet Ports to Add Structural Integrity to Suction Removable Fins on Intake for Directional Load and Turn Control 304- Shaft Stainless Steel Shaft (opt. Pre-Loader Shaft) Pre-Clearance Thrust Bearing Double Row -22 Bearings Performance 9 Vane Bowl System (optional 7 Vane) Full Exchange Value for exchange to Droops/Diverter Nozzles | ||
| Inesert Mold Available | $100.00 | |
| OPTIONS | ||
| -D | DROOP | $205.00 |
| -MD | MANUAL DIVERTER | $285.00 |
| -HTD | HYD. ASSY KIT FOR DIVERTER (MUST BE ORDERED WITH MANUAL DIVERTER) | $495.00 |
| (COMPLETE UNIT INCLUDING COILED STEERING WHEEL UP/DOWN SWITCH) | ||
 |
||
| 7000 | 7000 JR. DRIVE | $2,480.00 |
| JR Drive was designed to fit a large range of motor options from a 43 HP Geo. to a 4.3 V6 @ 260 HP.The JR Drive gets this wide range from Impeller & Bowl options available. Both thrust and performance are exceptional. | ||
| OPTIONS | ||
| -P | Full Polish | $275.00 |
| -D | DROOP | $205.00 |
| -MD | MANUAL DIVERTER | $285.00 |
| -HTD | HYD. ASSY KIT FOR DIVERTER (MUST BE ORDERED WITH MANUAL DIVERTER) | $495.00 |
| (COMPLETE UNIT INCLUDING COILED STEERING WHEEL UP/DOWN SWITCH) | ||
| BOWL STUFFER- Built Into Bowl | N/C | |
| RESEARCH & DEVELOPMENT | ||
6960 Aragon Cir. #2 Buena Park, Ca. 90620